IEEE 802.1d compliance 16K MAC address entries MAC address learning and aging Static, dynamic, and blackhole MAC address entries Packet filtering based on source MAC addresses
VLAN
4K VLANs Guest VLANs, voice VLAN, and super VLAN MUX VLAN and GVRP VLAN assignment based on MAC addresses, protocols, and IP subnets QinQ Selective QinQ 1:1 VLAN mapping N:1 VLAN mapping
Reliability
RRPP (ring topology, intersecting rings, and multi-instance), implementing protection switchover within 50 ms Smart Link tree topology and Smart Link multi-instance, providing the millisecond-level protection switchover STP(IEEE 802.1d), RSTP(IEEE 802.1w), and MSTP(IEEE 802.1s) BPDU protection, root protection, and loop protection Smart Ethernet Protection (SEP)
BFD for OSPF, BFD for IS-IS, BFD for VRRP, and BFD for PIM
IP routing
Static routing, RIPv1, RIPv2, and ECMP
OSPF, IS-IS, and BGP
IPv6 features
Neighbor Discovery (ND) Path MTU (PMTU) IPv6 ping, IPv6 tracert, and IPv6 Telnet Manually configured tunnel 6to4 tunnel ISATAP tunnel ACLs based on the source IPv6 address, destination IPv6 address, Layer 4 ports, or protocol type MLD v1/v2 snooping
Multicast
1 K multicast groups IGMP v1/v2/v3 snooping and IGMP fast leave Multicast VLAN and multicast replication between VLANs Multicast load balancing among member ports of a trunk Controllable multicast Port-based multicast traffic statistics
IGMP v1/v2/v3, PIM-SM, PIM-DM and PIM-SSM
QoS/ACL
Rate limiting on packets sent and received by an interface Packet redirection Port-based traffic policing and two-rate three-color CAR Eight queues on each port WRR, DRR, SP, WRR+SP, and DRR+SP queue scheduling algorithms Re-marking of the 802.1p priority and DSCP priority Packet filtering on Layers 2 through 4, filtering out invalid frames based on the source MAC address, destination MAC address, source IP address, destination IP address, port number, protocol type, and VLAN ID Rate limiting in each queue and traffic shaping on ports
Security
User privilege management and password protection DoS attack defense, ARP attack defense, and ICMP attack defense Binding of the IP address, MAC address, interface, and VLAN Port isolation, port security, and sticky MAC Blackhole MAC address entries Limit on the number of learned MAC addresses 802.1x authentication and limit on the number of users on an interface AAA authentication, RADIUS authentication, HWTACACS authentication, and NAC SSH v2.0 CPU defense Blacklist and whitelist
Surge protection
6KV surge protection capability on service ports (1KV on service ports on PoE devices)
Management and maintenance
iStack MAC Forced Forwarding (MFF) Remote configuration and maintenance using Telnet Auto-Config Virtual cable test Ethernet OAM (IEEE 802.3ah and 802.1ag) Dying gasp power-off alarm (S3700-28TP-EI-MC-AC) SNMP v1/v2c/v3 and RMON Web NMS
DC: Rated voltage range: –48V to –60V Maximum voltage range: –36V to –72V DC Note: PoE-support switches do not use DC power supplies.
Dimensions (W x D x H)
442 mm x 220 mm x 43.6 mm
Weight
S3700-28TP-EI<2.5Kg
Power consumption
S3700-28TP-EI<20W
Huawei S3700-28TP-EI-DC is next-generation Layer 3 Ethernet switch which supports IP multicasting and complex routing protocols (Static route, RIPv1, RIPv2, and ECMP, OSPF, IS-IS, and BGP).
Quick Specs
Figure 1 shows the appearance of Huawei S3700-28TP-EI-DC switch.
Table 1 shows the Quick Specs.
Product Code
S3700-28TP-EI-DC
Downlink Ports
24 x 10/100 Base-TX ports
Uplink Ports
2 x 1,000 Base-X SFP Ports
2 x Gigabit Combo Ports
(10/100/1,000 Base-T or 100/1,000 Base-X)
MAC Address
16K MAC address entries
VLAN
4K
Forwarding Performance
9.6 Mpps
Switching Capacity
64 Gbit/s
Stacking
Supported
Stack Connection Mode
Service Port Connection
Power
DC power supply
Heat Dissipation
Fan-free natural heat dissipation
Installation mode
Rack mounting, desk mounting, wall mounting
300-mm deep cabinet
Supported
Dimensions (W x D x H)
44.2 cm x 22 cm x 4.36 cm
Product Details
Figure 2 shows the front panel of Huawei S3700-28TP-EI-DC switch.
Note:
①
Ground Screw
⑤
2 x 1000BASE-X Ethernet optical interfaces
②
DC Power Terminals
⑥
2 x Gigabit Combo Ports
③
Power Switch
⑦
One Console Port
④
24 x 10/100BASE-TX Ethernet Electrical Ports
·Ground Screw is used with a ground cable.
·DC Power Terminals are used with DC Power cables
·Two Combo Ports include 10/100/1000BASE-T and 100/1000BASE-X ports. FE/GE/GE-CWDM optical transceivers are applicable to the combo ports.
·Huawei S3700-28TP-EI-DC switch supports Huawei Intelligent Stack Technology (iStack). Multiple S3700 switches can be connected with stack cables to set up a stack, which functions as a virtual switch.
Figure 3 shows the back looking of Huawei S3700-28TP-EI-DC switch.
The Transceiver
Huawei S3700-28TP-EI-DC supports FE optical transceivers, GE optical transceivers and GE-CWDM optical transceivers.
Table 2-4 shows the recommended optical transceivers.
Choosing a selection results in a full page refresh.
Opens in a new window.
Cookie Consent Popup
We use cookies to enhance your browsing experience, serve personalized ads or content, and analyze our traffics. By clicking "Allow Cookies" you consent to our use of cookie.
×
Please wait...
Make An Offer
"S3700-28TP-EI-DC(24 Ethernet 10\/100 ports,2 Gig SFP and 2 dual-purpose 10\/100\/1000 or SFP,DC -48V) - S3700-28TP-EI-DC"
£537.00
"S3700-28TP-EI-DC(24 Ethernet 10\/100 ports,2 Gig SFP and 2 dual-purpose 10\/100\/1000 or SFP,DC -48V) - S3700-28TP-EI-DC"